Cooling Tower - The Generation and Hazards of Freezing in Co[ 2025-06-10 ]

Generation and harm of freezing of cooling tower-cooling equipment When the cooling tower runs in winter in cold and severe cold areas, the temperature of circulating water is much lower than that in summer. Due to the influence of low temperature air, the equipment and foundation of Lingleng system may be frozen during operation and stop operation. The common parts are as follows 1. Watering filler When the drenching density of the outermost packing is generally low, cold air will invade people first, which is the most likely to cause freezing damage. When the dre

Attention should be paid to issues when using a reverse flow[ 2025-06-10 ]

Attention should be paid to issues when using a reverse flow cooling tower during hoisting 1. The difference between conventional counter current cooling towers ① The water spray density is as high as 16.5m3/(m2 h), while the water spray density of conventional counter current cooling towers generally does not exceed 12m3/(m2 h). A higher water spray density not only reduces the cost of circulating water, but also reduces the footprint of the lifting tower under the same output. ② The gas to water ratio is only 0.66 (the gas to water ratio of conventional count

What should be paid attention to when connecting pipes outsi[ 2025-06-10 ]

Precautions for external connection of cross flow cooling tower: 1. The pipes on both sides of the cooling tower should be kept as long as possible to ensure balanced resistance; 2. Each inlet and outlet pipe of the cooling tower should be equipped with a valve to regulate the water flow; 3. Pipeline design should be as simple and direct as possible; 4. Welding operations on the tower are prohibited. Welding should be carried out far away from the tower body, and then connected to the reserved inlet and outlet flanges of the cooling tower after completion.

What issues should be noted when selecting a cooling tower[ 2025-06-10 ]

Guidelines for Cooling Tower Selection 1. Please specify the specific model selected for the cooling tower or the flow rate processed per hour. 2. The inlet and outlet temperatures of the cooling tower, as well as the local wet bulb temperature. 3. Please explain what equipment is being used for cooling, whether there is a circulating water tank on site, and what the installation conditions are. 4. If spare parts and other accessories are needed, please indicate if there are any other requirements. 5. Please specify the usage environment and specific conditions for

A Brief Discussion on the Classification and Advantages of C[ 2025-06-10 ]

Jiangsu cooling tower, Jiangsu cooling tower manufacturers, cooling tower manufacturers, stainless steel cooling towers, glass fiber reinforced plastic cooling towers, specializing in the production of cooling towers. A, countercurrent tower: 1, water in the tower packing, water from top to bottom, air from bottom to top, the two flow to the opposite kind of cooling tower. 2. The counterflow cooling tower has good thermal performance and is divided into three cooling sections: (1) from the water distributor to the packing top, the water temperature in this section

Precautions for installation and use of cooling tower[ 2025-06-10 ]

Installation and usage precautions 1. It should be placed in a well ventilated and clean place. 2. The inlet pipe of the cross flow tower is installed on both sides and connected to the water distribution tank. Users should install butterfly valves at the connection point to regulate the flow rate. The inlet pipe can be introduced from the main pipe below, or the main pipe can be placed on the tower. At this time, the pipe support should be placed on the bracket on the side of the cooling tower. The outlet pipe can be connected to the tower bottom water tank in any

Installation, commissioning, and usage instructions for cool[ 2025-06-10 ]

1. The direction of the inlet and outlet pipes of a small counter current tower can be arbitrarily selected in a horizontal position, but it must not collide with the foundation. If there is a foundation in the middle, its load should be 25% of the operating weight, and the remaining 75% should be evenly borne by the peripheral rectangular foundation. If installed on the roof, the additional pressure caused by the load should be considered. 2. A bracket should be installed at the connection between the cooling tower and the inlet and outlet pipes to prevent excessi